Knowledge Guide on Extruders for PVC Pipe Production




Ningbo Fangli Technology Co., Ltd. is a mechanical equipment manufacturer with over 30 years’ experiences of plastic pipe extrusion equipment, new environmental protection and new materials equipment. Since its establishment Fangli has been developed based on user’s demands. Through continuous improvement, independent R&D on the core technology and digestion & absorption of advanced technology and other means, we have developed PVC pipe extrusion line, PP-R pipe extrusion line, PE water supply / gas pipe extrusion line, PVC-O pipe extrusion line, RTP pipe extrusion line, which was recommended by the Chinese Ministry of Construction to replace imported products. We have gained the title of “First-class Brand in Zhejiang Province”.


Extrusion molding is one of the fundamental molding methods in plastics processing, and most thermoplastics can be processed by this method. Its characteristics are: the production process is continuous, and therefore the products are also continuous; production efficiency is high and investment is low. The extrusion molding process proceeds as follows: the plastic is heated and subjected to friction and shear to bring it into a viscous flow state; under pressure, it is forced through a die of a certain shape to form a continuous body whose cross-section resembles the die shape; it is then cooled to give it a certain geometric shape and dimensions, yielding the required product.


Production flow: Extrusion → Sizing and cooling → Printing → Cutting → Inspection → Packaging → Warehousing


I. Composition of the Production Line

An extruder consists of the main machine, the die head, the sizing and cooling device, the printing device, the cutting device, etc.


(I) Main Machine

1. Screw and Barrel


The screw is the heart of the extruder; everything is directly or indirectly centered on the screw. It conveys, mixes, and plasticizes the material and directly affects product quality. According to the changes in the material along the screw, the screw is usually divided into three sections: the feed section, the compression section (melting section), and the metering section (homogenizing section).


Feed section: generally the first zone. The feed section of a twin screw has deeper screw channels and a larger volume, which facilitates increased material input and compression. The temperature in this zone must generally not be too high; otherwise, molten material may adhere to the surface of the feed opening, causing material flow faults or bridging and interrupted feeding into the extruder.


Compression section: generally the second and third zones. This section is characterized by changes in screw pitch, interrupted threads, and uniformly varying thread width. The material is strongly compressed and, under shear action, is well plasticized and mixed. This section is provided with a vacuum vent to discharge gases from the material.


Metering section: the screw channels in this section are the shallowest in the entire screw and have the smallest volume; the screw and thread form remain essentially unchanged. The molten and plasticized material is further compressed in this section and made uniform and refined. Because the material moves relatively uniformly in this section, extrusion fluctuations are reduced, and the stability of the melt flow entering the die is improved.


Twin screws can be classified by center distance into intermeshing and non-intermeshing types; by direction of rotation into co-rotating and counter-rotating types; and by relative axial position into parallel twin screws and conical twin screws. Conical twin screws are suitable for PVC pipes, profiles, corrugated pipes, etc.; parallel twin screws are suitable for large products such as pipes above D400.


The extruder commonly used is the counter-rotating conical twin-screw extruder. Its working characteristics are as follows:


(1) Forced conveying action: In a counter-rotating, fully intermeshing twin-screw extruder, the two screws mesh with each other; at the meshing point, the thread of one screw inserts into the screw channel of the other, so that no backflow or stagnation occurs during material conveying. Regardless of whether the screw channels are fully filled, the conveying speed remains essentially constant, giving strong conveying capability.


(2) Mixing action: Because the two screws intermesh, the material undergoes far more complex motion during extrusion than in a single-screw extruder, continuously experiencing longitudinal and transverse shear mixing, thereby generating a large amount of heat energy and making the residence time of the material in the barrel shorter than in a single-screw extruder.


(3) Self-cleaning action: If accumulated material adhering to the screw channels remains for too long, it will cause degradation of the material and seriously impair product quality. Therefore, accumulated material should be removed promptly, especially for the heat-sensitive plastic PVC. In counter-rotating twin screws, a speed difference exists between the thread and the screw channel at the meshing point; during mutual wiping, the material adhering to the screws is peeled off, giving the screws a self-cleaning effect.


Geometric parameters of a single screw:


(1) Screw diameter Ds: refers to the outer diameter, usually between 30 and 200 mm.


(2) Screw length-to-diameter ratio L/Ds: the ratio of the effective length of the screw working part to the diameter Ds, commonly 15–25 (up to 40 in recent years). A large L/Ds improves the temperature distribution of the plastic, makes mixing more uniform, reduces backflow and leakage flow in extrusion, and increases output; a small L/Ds is unfavorable for mixing and plasticization of the plastic. Therefore, for rigid plastics, powdered plastics, or crystalline plastics that require long plasticizing times, a screw with a large L/Ds should be selected; for heat-sensitive plastics, which decompose after too long exposure to heat, a screw with a small L/Ds should be selected.


(3) Screw compression ratio A: the ratio of the volume of the first screw channel in the feed section to the volume of the last screw channel in the homogenizing section. It represents the degree to which the plastic is compressed throughout the entire screw. The larger A is, the greater the squeezing action on the plastic and the stronger the ability to remove air from the material. Generally A is 2–5 (rigid PVC: 3–4).


(4) Screw channel depth H: affects plasticization and extrusion efficiency. When H is small, a higher shear rate can be generated on the plastic, which is favorable for heat transfer and plasticization, but extrusion production efficiency is low. Therefore, heat-sensitive plastics use deep channels (e.g., PVC), while plastics with high melt viscosity and high thermal stability (e.g., PA) use shallow channels. The feed section channel depth H₁ is a fixed value, generally H₁ > 0.1Ds; the compression section H₂ is a variable value; the homogenizing section H₃ is a fixed value, H₃ = 0.02–0.06Ds.


(5) Helix angle: the angle between the thread and the screw cross-section. As θ increases, output increases but shear decreases. θ is between 10° and 30°. θ = 30° is suitable for powder, θ = 15° for square pellets, and θ = 17° for cylindrical pellets. In the homogenizing section, extrusion output is highest when θ = 30°. For machining convenience, taking Ds = Ls gives θ = 17.7°, which is the commonly used screw.


(6) Thread flight width E: too small increases leakage flow and reduces output; too large increases power consumption. Generally E = 0.08–0.12Ds.


(7) Screw clearance δ: its size directly affects the production capacity of the extruder and the plasticization of the material. δ = 0.1–0.65 mm is appropriate. For large screws, δ = 0.002Ds; for small screws, δ = 0.005Ds.


Barrel: The barrel and screw together form the basic structure of the extrusion system. Because the third and fourth zones of the barrel heat up relatively quickly, cooling devices are generally provided.


2. Die Head and Die


The die head and die are crucial parts of plastics molding processing. Conventionally, the die head connector assembly is collectively called the die head; it consists of the breaker plate, torpedo (spreader), support, die, and mandrel.


Function of the die head: to change the melt from spiral motion to linear motion, generate molding pressure, and further densify and uniformly plasticize the melt.


a. Breaker plate: divided into perforated plate and straight-through plate. Functions: increase back pressure, plasticize the melt, homogenize the melt, and change the melt from spiral motion to linear motion.


b. Spreader and support: There is a cavity between the spreader and the breaker plate. This cavity serves to collect the material stream, supplement plasticization, and recombine the flow. Therefore, the distance between the spreader and the breaker plate should not be too small, to avoid uneven discharge; if too large, the material residence time is long and decomposition is likely. Generally 10–20 mm.


II. Sizing and Cooling Device (Note: regularly clean support rollers, spray nozzles, and water tanks)

When the pipe exits the die, it has a fairly high temperature. To stabilize and size the extruded product and obtain the required product cross-sectional shape, dimensions, and glossy surface, the extruded pipe blank must immediately be processed through the sizing and cooling device.


The sizing method we use is the outer-diameter sizing vacuum negative-pressure method. Its characteristics are convenient operation and little waste, but when the pipe diameter is large, the vacuum suction is difficult to control for roundness. Small-diameter pipes use immersion cooling; because the buoyancy in the water tank is relatively large, bending is likely to occur. Therefore, large-diameter pipes use spray water cooling. There are generally four spray water pipes, evenly distributed around the pipe, with denser spraying near the sizing sleeve end.


This device consists of a frame, vacuum sizing water tank forward/backward adjustment device, left/right adjustment device, height adjustment device, vacuum pump system, and water pump system.


III. Printing Device: Inkjet Printer and Color Printing Machine

Working principle of the color printing machine: Using the traction force of the haul-off device and the friction torque generated when the rubber driving wheel and support wheel clamp the pipe, the printing wheel and rubber color-printing wheel are driven to rotate. A blade scrapes the ink clean from the circumferential surface of the rotating printing wheel, leaving ink only in the recesses of the characters. The printing wheel transfers the marked characters onto the rubber color-printing wheel, which then prints them onto the surface of the pipe. The color printing machine consists of four major components: the frame, the color-printing wheel, the support wheel, and the air-blower drying device.


IV. Haul-off Unit

Its function is to provide a certain traction force and haul-off speed to the pipe that has already obtained a preliminary shape and dimensions from the die head, to draw out the pipe uniformly, and to adjust the pipe wall thickness through traction.


Note: air pressure, crawler track, electrical position.


V. Cutting machine

When the pipe reaches the required length, an instruction is issued through an electronic length counter or limit switch, and the cutting machine starts to work. The length dimension must be accurate, and the cut must be uniform and flat.


If you need more information, Ningbo Fangli Technology Co., Ltd. welcomes you to contact for a detailed inquiry, we will provide you with professional technical guidance or equipment procurement suggestions.


Navigation